1. An (a) __________ reaction liberates heat and the temperature of the reaction mixture increases.
Answer
Correct Answer:
Exothermic
Note: This Question is unanswered, help us to find answer for this one
2. The clearance volume of a compressor cylinder is the ____.
Answer
Correct Answer:
Volume of the space between the bottom of the valve plate and the top of the piston at top dead-center
Note: This Question is unanswered, help us to find answer for this one
3. A what is a heat sink?
Answer
Correct Answer:
A heat reservoir that absorbs energy in the form of heat
Note: This Question is unanswered, help us to find answer for this one
4. What does a heat sink absorb?
Answer
Correct Answer:
Energy in the form of heat
Note: This Question is unanswered, help us to find answer for this one
5. What does a heat sink do?
Answer
Correct Answer:
Absorbs energy in the form of heat
Note: This Question is unanswered, help us to find answer for this one
6. A reservoir that can supply or absorb energy in the form of heat is known as what?
Answer
Correct Answer:
Thermal energy reservoir
Note: This Question is unanswered, help us to find answer for this one
7. What are thermal energy reservoirs?
Answer
Correct Answer:
Heat reservoir
Note: This Question is unanswered, help us to find answer for this one
8. What is a reservoir capable of doing?
Answer
Correct Answer:
Supply or absorb energy
Note: This Question is unanswered, help us to find answer for this one
9. How many Btu
Answer
Correct Answer:
1
Note: This Question is unanswered, help us to find answer for this one
10. What is the expression of the conversion efficiency of power plants in the US?
Answer
Correct Answer:
Heat rate
Note: This Question is unanswered, help us to find answer for this one
11. What is the conversion efficiency of power plants in the US?
Answer
Correct Answer:
Rate
Note: This Question is unanswered, help us to find answer for this one
12. What is the heat pump coefficient of performance expressed as?
Answer
Correct Answer:
Desired output divided by required input
Note: This Question is unanswered, help us to find answer for this one
13. What is the cyclic device that causes the transfer of heat from a low-temperature region to a high-temperature region?
Answer
Correct Answer:
Heat pump
Note: This Question is unanswered, help us to find answer for this one
14. What kind of products are produced when a fuel is burned?
Answer
Correct Answer:
Combustion products
Note: This Question is unanswered, help us to find answer for this one
15. How much heat would a fuel release when burned completely?
Answer
Correct Answer:
Heating value of a fuel
Note: This Question is unanswered, help us to find answer for this one
16. The value of a fuel
Answer
Correct Answer:
Enthalpy of combustion
Note: This Question is unanswered, help us to find answer for this one
17. What are heat exchangers used for?
Answer
Correct Answer:
Various industries
Note: This Question is unanswered, help us to find answer for this one
18. What kind of heat exchanger has two pipes that are different sizes?
Answer
Correct Answer:
Double-tube
Note: This Question is unanswered, help us to find answer for this one
19. What are engines designed to convert?
Answer
Correct Answer:
Other forms of energy
Note: This Question is unanswered, help us to find answer for this one
20. What are engines designed for?
Answer
Correct Answer:
Converting other forms of energy
Note: This Question is unanswered, help us to find answer for this one
21. What are absorption refrigeration systems often classified as?
Answer
Correct Answer:
Heat-driven systems
Note: This Question is unanswered, help us to find answer for this one
22. A system and its surroundings are called what?
Answer
Correct Answer:
Two systems
Note: This Question is unanswered, help us to find answer for this one
23. What is defined as the form of energy that is transferred between systems by virtue of a temperature difference?
Answer
Correct Answer:
Heat
Note: This Question is unanswered, help us to find answer for this one
24. Gravitational acceleration g is what percent less at 30,000 than it is at sea level?
Answer
Correct Answer:
Less than 1 percent
Note: This Question is unanswered, help us to find answer for this one
25. What is the gravitational acceleration at sea level?
Answer
Correct Answer:
9.807 m/s2
Note: This Question is unanswered, help us to find answer for this one
26. What type of analysis gives the mass of each component of a mixture?
Answer
Correct Answer:
Gravimetric
Note: This Question is unanswered, help us to find answer for this one
27. What is the name of the process used to determine the composition of a mixture?
Answer
Correct Answer:
Gravimetric analysis
Note: This Question is unanswered, help us to find answer for this one
28. What is a rule that describes multicomponent, multiphase systems?
Answer
Correct Answer:
Gibbs phase rule
Note: This Question is unanswered, help us to find answer for this one
29. What does the Gibbs phase rule provide the number of?
Answer
Correct Answer:
Independent variables
Note: This Question is unanswered, help us to find answer for this one
30. What does Gibbs-Dalton law say about the behavior of a gas components in a mixture?
Answer
Correct Answer:
Behaves as if it exists alone at the mixture temperature
Note: This Question is unanswered, help us to find answer for this one
31. In a mixture of gases, the behavior of each component is what under the ideal-gas approximation?
Answer
Correct Answer:
As if it exists alone
Note: This Question is unanswered, help us to find answer for this one
32. What is the law that states a gas component behaves as if it exists alone at the mixture temperature and mixture volume?
Answer
Correct Answer:
Gibbs-Dalton law
Note: This Question is unanswered, help us to find answer for this one
33. What do heat pumps use the ground for?
Answer
Correct Answer:
Heat source
Note: This Question is unanswered, help us to find answer for this one
34. What is a ground-source heat pump?
Answer
Correct Answer:
Geothermal heat pumps
Note: This Question is unanswered, help us to find answer for this one
35. What are the inputs to a generator?
Answer
Correct Answer:
Mechanical power
Note: This Question is unanswered, help us to find answer for this one
36. What is a generator
Answer
Correct Answer:
Generator efficiency
Note: This Question is unanswered, help us to find answer for this one
37. Electrical energy is derived from what type of device?
Answer
Correct Answer:
Generator
Note: This Question is unanswered, help us to find answer for this one
38. What is a plot of the entropy departure factor used to determine?
Answer
Correct Answer:
The deviation of the entropy of a gas
Note: This Question is unanswered, help us to find answer for this one
39. What is the deviation of the entropy of a gas at a given P and T from the entropy of an ideal gas at the same P and T indicated with the term departure chart?
Note: This Question is unanswered, help us to find answer for this one
42. What does the name gasses seem to obey?
Answer
Correct Answer:
Corresponding states
Note: This Question is unanswered, help us to find answer for this one
43. What type of chart shows that gases seem to obey the principle of corresponding states reasonably well?
Answer
Correct Answer:
Generalized compressibility chart
Note: This Question is unanswered, help us to find answer for this one
44. What is the working fluid in a gas refrigeration cycle?
Answer
Correct Answer:
Lower-temperature fluid
Note: This Question is unanswered, help us to find answer for this one
45. The lower-temperature working fluid is used to produce what effect?
Answer
Correct Answer:
Refrigeration
Note: This Question is unanswered, help us to find answer for this one
46. What remains a gas throughout the entire cycle in a gas power cycle?
Answer
Correct Answer:
The working fluid
Note: This Question is unanswered, help us to find answer for this one
47. What are cycles where the working fluid remains a gas throughout the entire cycle?
Answer
Correct Answer:
Gas power cycles
Note: This Question is unanswered, help us to find answer for this one
48. What is constantly occurring when molecules are in a container?
Answer
Correct Answer:
Colliding with each other
Note: This Question is unanswered, help us to find answer for this one
49. What is the phase of a substance that has molecules that are far apart from each other?
Answer
Correct Answer:
Gas phase
Note: This Question is unanswered, help us to find answer for this one
50. What determines the value of R for each gas?
Answer
Correct Answer:
R = Ru/M
Note: This Question is unanswered, help us to find answer for this one
51. What does the Gage pressure represent?
Answer
Correct Answer:
The difference between the absolute pressure and the local atmospheric pressure
Note: This Question is unanswered, help us to find answer for this one
52. What is the difference between the absolute pressure and the local atmospheric pressure?
Answer
Correct Answer:
Gage pressure
Note: This Question is unanswered, help us to find answer for this one
53. What is the chemical energy of a fuel cell converted to?
Answer
Correct Answer:
Electric energy
Note: This Question is unanswered, help us to find answer for this one
54. What is the name of the efficiency limit of a fuel cell?
Answer
Correct Answer:
Carnot
Note: This Question is unanswered, help us to find answer for this one
55. What are fuel cells not?
Answer
Correct Answer:
Heat engines
Note: This Question is unanswered, help us to find answer for this one
56. What is the ratio of air to fuel in an engine?
Answer
Correct Answer:
Fuel-air ratio
Note: This Question is unanswered, help us to find answer for this one
57. The fuel-air ratio is the reciprocal of what?
Answer
Correct Answer:
Air-fuel ratio
Note: This Question is unanswered, help us to find answer for this one
58. What can be used as fuel to release energy?
Answer
Correct Answer:
Material
Note: This Question is unanswered, help us to find answer for this one
59. What kind of material can be burned?
Answer
Correct Answer:
Fuel
Note: This Question is unanswered, help us to find answer for this one
60. A four stroke engine has an odd number of cycles per cylinder, so it has an even total number of cycles per revolution. How many revolutions per thermodynamic cycle is that?
Answer
Correct Answer:
Two
Note: This Question is unanswered, help us to find answer for this one
61. What does the crankshaft complete for each thermodynamic cycle?
Answer
Correct Answer:
Two revolutions
Note: This Question is unanswered, help us to find answer for this one
62. What is the name of the convention that defines the direction of heat transfer and work?
Answer
Correct Answer:
Sign convention
Note: This Question is unanswered, help us to find answer for this one
63. What is the sign convention for heat and work interactions?
Answer
Correct Answer:
Formal sign convention
Note: This Question is unanswered, help us to find answer for this one
64. What is a forced-draft cooling tower?
Answer
Correct Answer:
A wet cooling tower
Note: This Question is unanswered, help us to find answer for this one
65. What is the technical term for forced-draft cooling tower?
Answer
Correct Answer:
Induced-draft cooling tower
Note: This Question is unanswered, help us to find answer for this one
66. What is the value of flow work on a unit mass basis?
Answer
Correct Answer:
Pv
Note: This Question is unanswered, help us to find answer for this one
67. Air that is rapidly compressed undergoes _________.
Answer
Correct Answer:
Increase in temperature;
Note: This Question is unanswered, help us to find answer for this one
68. The _____ law of thermodynamics states that not all energy is used because _____.
Answer
Correct Answer:
Second; some of the energy disperses as heat
Note: This Question is unanswered, help us to find answer for this one
69. δh for an endothermic process is ________ while δh for an exothermic process is ________.
Answer
Correct Answer:
Positive, negative
Note: This Question is unanswered, help us to find answer for this one
70. When you click through to the end of a presentation, ________ displays.
Answer
Correct Answer:
Blank Slide
Note: This Question is unanswered, help us to find answer for this one
71. When the quantity q is greater than zero, __________ is added to the system.
Answer
Correct Answer:
Heat
Note: This Question is unanswered, help us to find answer for this one
72. The entropy of an isolated system _________.
Answer
Correct Answer:
Always increases or remains constant.
Note: This Question is unanswered, help us to find answer for this one
73. Spontaneous reactions _____.
Answer
Correct Answer:
Always result in increased disorder of the system
Note: This Question is unanswered, help us to find answer for this one
74. The thermodynamic processes that occur in nature ____________.
Answer
Correct Answer:
Convert thermal energy into mechanical energy
Note: This Question is unanswered, help us to find answer for this one
75. The internal energy of a system is always increased by __________.
Answer
Correct Answer:
Adding heat to the system
Note: This Question is unanswered, help us to find answer for this one
76. Inborn or intrinsic reflexes are ________.
Answer
Correct Answer:
Involuntary, yet may be modified by learned behavior
Note: This Question is unanswered, help us to find answer for this one
77. Internal energy undergoes changes when there are corresponding changes in _________.
Answer
Correct Answer:
Temperature
Note: This Question is unanswered, help us to find answer for this one
78. Energy cannot be _______.
Answer
Correct Answer:
Destroyed
Note: This Question is unanswered, help us to find answer for this one
79. As entropy in a system increases, energy in the system _________.
Answer
Correct Answer:
Becomes less ordered
Note: This Question is unanswered, help us to find answer for this one
80. The amount of heat required to raise the temperature of the unit mass of gas through one degree at constant volume, is called
Answer
Correct Answer:
Specific heat at cOnstant volume
Note: This Question is unanswered, help us to find answer for this one
81. There is no change in internal energy in an isothermal process.
Answer
Correct Answer:
Correct
Note: This Question is unanswered, help us to find answer for this one
82. The distillation carried out in such a way that the liquid with the lowest boiling point is first evaporated and recondensed, then the liquid with the next higher boiling point is then evaporated and recondensed, and so on until all the available liquid fuels are separately recovered in the sequence of their boiling points. Such a process is called
Answer
Correct Answer:
Fractional distillation
Note: This Question is unanswered, help us to find answer for this one
83. The entropy __________ in an irreversible cyclic process.
Answer
Correct Answer:
Increases
Note: This Question is unanswered, help us to find answer for this one
84. The pressure exerted by an ideal gas is __________ of the kinetic energy of all the molecules contained in a unit volume of gas.
Answer
Correct Answer:
Two-third
Note: This Question is unanswered, help us to find answer for this one
85. The efficiency and work ratio of a simple gas turbine cycle are
Answer
Correct Answer:
Very low
Note: This Question is unanswered, help us to find answer for this one
86. The processes occuring in open system which permit the transfer of mass to and from the system, are known as
Answer
Correct Answer:
Flow processes
Note: This Question is unanswered, help us to find answer for this one
87. Workdone in a free expansion process is
Answer
Correct Answer:
Zero
Note: This Question is unanswered, help us to find answer for this one
88. Water gas is obtained by passing air and a large amount of steam over waste coal at about 650°C.
Answer
Correct Answer:
Incorrect
Note: This Question is unanswered, help us to find answer for this one
89. The value of specific heat at constant pressure (Cp) is __________ that of at constant volume (Cv).
Answer
Correct Answer:
More than
Note: This Question is unanswered, help us to find answer for this one
90. The value of gas constant (R) in S. I. units is
Answer
Correct Answer:
287 J/kgK
Note: This Question is unanswered, help us to find answer for this one
91. The ratio of specific heat at constant pressure (Cp) and specific heat at constant volume (Cv) is
Answer
Correct Answer:
Greater than one
Note: This Question is unanswered, help us to find answer for this one
92. The efficiency of Diesel cycle approaches to Otto cycle efficiency when
Answer
Correct Answer:
Cut-off is zero
Note: This Question is unanswered, help us to find answer for this one
93. In the first law of thermodynamics, the total energy of the system remains constant.
Answer
Correct Answer:
True
Note: This Question is unanswered, help us to find answer for this one
94. A cycle consisting of one constant pressure, one constant volume and two isentropic processes is known as
Answer
Correct Answer:
Diesel cycle
Note: This Question is unanswered, help us to find answer for this one
95. An adiabatic process is one in which
Answer
Correct Answer:
All of these
Note: This Question is unanswered, help us to find answer for this one
96. The compression ratio for petrol engines is
Answer
Correct Answer:
5 to 8
Note: This Question is unanswered, help us to find answer for this one
97. Which of the following has the minimum atomic mass?
Answer
Correct Answer:
Carbon
Note: This Question is unanswered, help us to find answer for this one
98. All the commercial liquid fuels are derived from natural petroleum (or crude oil).
Answer
Correct Answer:
True
Note: This Question is unanswered, help us to find answer for this one
99. According to Gay-Lussac law for a perfect gas, p/T = constant, if v is kept constant.
Answer
Correct Answer:
True
Note: This Question is unanswered, help us to find answer for this one
