1. The property of a material which enables it to resist fracture due to high impact loads is known as
Answer
Correct Answer:
Toughness
Note: This Question is unanswered, help us to find answer for this one
2. The permissible stress for carbon steel under static loading is generally taken as
Answer
Correct Answer:
4000-4500 kg/cm2
Note: This Question is unanswered, help us to find answer for this one
3. The ultimate strength of steel in tension in comparison to shear is in the ratio of
Answer
Correct Answer:
3 : 2
Note: This Question is unanswered, help us to find answer for this one
4. What is an example of an undercut?
Answer
Correct Answer:
A cut having inward sloping sides with an overhanging edge
Note: This Question is unanswered, help us to find answer for this one
5. What type of cut has inward sloping sides with an overhanging edge?
Answer
Correct Answer:
Undercut
Note: This Question is unanswered, help us to find answer for this one
6. What is dedicated to making components?
Answer
Correct Answer:
Tooling
Note: This Question is unanswered, help us to find answer for this one
7. What are the two definitions of a hand tool?
Answer
Correct Answer:
Powered by hand rather than a motor
Note: This Question is unanswered, help us to find answer for this one
8. What is a device that is necessary to, or aids in the performance of a specific operation?
Answer
Correct Answer:
A tool
Note: This Question is unanswered, help us to find answer for this one
9. What is the maximum limit of a dimension?
Answer
Correct Answer:
Upper
Note: This Question is unanswered, help us to find answer for this one
10. What is used to control the manufacturing process more accurately?
Answer
Correct Answer:
Tolerances
Note: This Question is unanswered, help us to find answer for this one
11. What is a border table usually located on?
Answer
Correct Answer:
The bottom or lower right-hand corner of a manufacturing drawing
Note: This Question is unanswered, help us to find answer for this one
12. What is the name of the border table usually located on the bottom or lower right-hand corner of a manufacturing drawing?
Answer
Correct Answer:
Title Block
Note: This Question is unanswered, help us to find answer for this one
13. What is a sort of thermal analysis that helps to tailor the thermal management solution for optimal performance?
Answer
Correct Answer:
Thermal Simulation
Note: This Question is unanswered, help us to find answer for this one
14. What can be used to dissipate heat in a system?
Answer
Correct Answer:
Heatsinks and fans for air cooling
Note: This Question is unanswered, help us to find answer for this one
15. What is the name for the ability to control the temperature of a system by means of technology based on Thermodynamics and Heat Transfer?
Answer
Correct Answer:
Thermal Management
Note: This Question is unanswered, help us to find answer for this one
16. What can't be used to attach a fastener that has a tapped hole?
Answer
Correct Answer:
Nut and bolt
Note: This Question is unanswered, help us to find answer for this one
17. In what material can you find a tapped hole?
Answer
Correct Answer:
Metals
Note: This Question is unanswered, help us to find answer for this one
18. What kind of tool does a tap have?
Answer
Correct Answer:
Internal screw thread
Note: This Question is unanswered, help us to find answer for this one
19. Architecture is a formal description and representation of a system organized in a way that supports what?
Answer
Correct Answer:
Reasoning
Note: This Question is unanswered, help us to find answer for this one
20. What is the formal description and representation of a system?
Answer
Correct Answer:
Architecture description
Note: This Question is unanswered, help us to find answer for this one
21. What kind of job is it to be an architect?
Answer
Correct Answer:
Technology professional
Note: This Question is unanswered, help us to find answer for this one
22. What is a technology professional who defines and implements architecture of a complex system referred to as?
Answer
Correct Answer:
System Architect
Note: This Question is unanswered, help us to find answer for this one
23. What is a type of Subassembly?
Answer
Correct Answer:
An assembled unit that is produced separately but is incorporated into a larger assembly
Note: This Question is unanswered, help us to find answer for this one
24. What is an example of an assebly that is produced separately but is incorporated into a larger assembly?
Answer
Correct Answer:
Subassembly
Note: This Question is unanswered, help us to find answer for this one
25. Standard for the Exchange of Product Data is better known as what?
Answer
Correct Answer:
Computer 3D model file format
Note: This Question is unanswered, help us to find answer for this one
26. What kind of separator positions assemblies at predetermined distances?
Answer
Correct Answer:
Threaded
Note: This Question is unanswered, help us to find answer for this one
27. What type of feature is faced on the spotface of a part?
Answer
Correct Answer:
Smooth, flat, accurately located contact surface
Note: This Question is unanswered, help us to find answer for this one
28. What is the term for a cylindrical pattern of ridges or teeth on a drive shaft?
Answer
Correct Answer:
Spline
Note: This Question is unanswered, help us to find answer for this one
29. What are commonly used to free-hand sketches?
Answer
Correct Answer:
Pen or a pencil
Note: This Question is unanswered, help us to find answer for this one
30. Minimum permissible chamfer dimensions are four times taller than what?
Answer
Correct Answer:
Shoulder
Note: This Question is unanswered, help us to find answer for this one
31. What are minimum dimensions of the shoulder planes of a shaft?
Answer
Correct Answer:
Four times taller
Note: This Question is unanswered, help us to find answer for this one
32. What is a schematic called when it is of mechanical systems?
Answer
Correct Answer:
Structural or procedural diagram
Note: This Question is unanswered, help us to find answer for this one
33. What is the ratio of size to actual size in a drawing with a scale of 1:5?
Answer
Correct Answer:
Downscaling
Note: This Question is unanswered, help us to find answer for this one
34. A sample can represent a material or process without necessarily being in the form of what?
Answer
Correct Answer:
The design in progress
Note: This Question is unanswered, help us to find answer for this one
35. What does a sample represent in a prototype?
Answer
Correct Answer:
A material or process
Note: This Question is unanswered, help us to find answer for this one
36. What is the purpose of research when it is done on materials and sources?
Answer
Correct Answer:
Establish facts and reach new conclusions
Note: This Question is unanswered, help us to find answer for this one
37. What two types of research are common during a project?
Answer
Correct Answer:
User research, competitor research
Note: This Question is unanswered, help us to find answer for this one
38. What type of image is synthesized from 3D CAD model data?
Answer
Correct Answer:
Photorealistic or non-photorealistic
Note: This Question is unanswered, help us to find answer for this one
39. What is the process of getting the final assembled animation scenes or pieces out of the computer in the format of a sequence of individual frames with rendered images?
Answer
Correct Answer:
Rendered Animation
Note: This Question is unanswered, help us to find answer for this one
40. What kind of software is used to create 3D CAD images?
Answer
Correct Answer:
3D CAD software
Note: This Question is unanswered, help us to find answer for this one
41. What is a render used for when used in advertising?
Answer
Correct Answer:
Design visualization
Note: This Question is unanswered, help us to find answer for this one
42. What does a relief groove provide for the cutting edge of a tool?
Answer
Correct Answer:
Clearance
Note: This Question is unanswered, help us to find answer for this one
43. What type of technology allows a model to be created by adding layers of materials?
Answer
Correct Answer:
Rapid prototyping
Note: This Question is unanswered, help us to find answer for this one
44. What is another term for rapid prototyping?
Answer
Correct Answer:
Additive layer manufacturing
Note: This Question is unanswered, help us to find answer for this one
45. What does the rack do when the pinion is pushed into rotation?
Answer
Correct Answer:
Be driven linearly
Note: This Question is unanswered, help us to find answer for this one
46. What is the term used to describe a type of linear actuator?
Answer
Correct Answer:
Rack’n’pinion
Note: This Question is unanswered, help us to find answer for this one
47. Quality Management Systems are focused on achieving what?
Answer
Correct Answer:
Quality objectives
Note: This Question is unanswered, help us to find answer for this one
48. What is expressed as the organizational structure, policies, procedures, processes and resources needed to achieve the desired standard of quality?
Answer
Correct Answer:
Quality Management Systems
Note: This Question is unanswered, help us to find answer for this one
49. What is a process in which the quality of all factors involved in production is reviewed?
Answer
Correct Answer:
Quality Control
Note: This Question is unanswered, help us to find answer for this one
50. Quality assurance is a way to improve and stabilize production by means of?
Answer
Correct Answer:
Preventing mistakes and defects
Note: This Question is unanswered, help us to find answer for this one
51. How is a prototype used to evaluate a new design?
Answer
Correct Answer:
Digitally
Note: This Question is unanswered, help us to find answer for this one
52. How could prototype be enhanced digitally?
Answer
Correct Answer:
With 3D models, renderings, and animations
Note: This Question is unanswered, help us to find answer for this one
53. What can be used to build a prototype physically?
Answer
Correct Answer:
3D printers
Note: This Question is unanswered, help us to find answer for this one
54. In what area is Proposal used?
Answer
Correct Answer:
Design project
Note: This Question is unanswered, help us to find answer for this one
55. Proposal is another word for what?
Answer
Correct Answer:
Act of putting forward or stating an approach to a design project for consideration
Note: This Question is unanswered, help us to find answer for this one
56. What does "proposal" mean in the context of architecture?
Answer
Correct Answer:
An act of putting forward or stating an approach to a design project for consideration
Note: This Question is unanswered, help us to find answer for this one
57. Along with a product, what may a project be defined as?
Answer
Correct Answer:
A piece of stand-alone research task or a conceptual development
Note: This Question is unanswered, help us to find answer for this one
58. What are title blocks called?
Answer
Correct Answer:
On all individual drawings
Note: This Question is unanswered, help us to find answer for this one
59. What is another name for the drawing commonly referred to as the production drawing?
Answer
Correct Answer:
Manufacturing Drawing
Note: This Question is unanswered, help us to find answer for this one
60. What would increase the bearing rigidity?
Answer
Correct Answer:
Bearing preloading
Note: This Question is unanswered, help us to find answer for this one
61. What does preloading a bearing do?
Answer
Correct Answer:
Increases bearing rigidity
Note: This Question is unanswered, help us to find answer for this one
62. What is the name of the outer ring gear in an epicyclic gear train?
Answer
Correct Answer:
Annulus
Note: This Question is unanswered, help us to find answer for this one
63. What is an example of an epicyclic gear train?
Answer
Correct Answer:
Planetary Gears
Note: This Question is unanswered, help us to find answer for this one
64. Pitch is the distance between a point on one tooth and the corresponding point on an adjacent tooth. Pitch is also the distance between threads expressed in what?
Answer
Correct Answer:
Millimeters
Note: This Question is unanswered, help us to find answer for this one
65. What is the term used to describe a gear that drives the other gear?
Answer
Correct Answer:
Pinion
Note: This Question is unanswered, help us to find answer for this one
66. What is Pilot Run a small scale experimental production run to analyze the results for?
Answer
Correct Answer:
Necessary corrections
Note: This Question is unanswered, help us to find answer for this one
67. What does a project have during its research phase?
Answer
Correct Answer:
Problem definition phase
Note: This Question is unanswered, help us to find answer for this one
68. What is a term that refers to a distinct period or stage within a design program?
Answer
Correct Answer:
Phase In Design
Note: This Question is unanswered, help us to find answer for this one
69. What type of data is managed in PDM?
Answer
Correct Answer:
Design data
Note: This Question is unanswered, help us to find answer for this one
70. What is another term for BOMs?
Answer
Correct Answer:
Bills of Materials
Note: This Question is unanswered, help us to find answer for this one
71. What are PCBs called when they have only one copper layer?
Answer
Correct Answer:
Single sided
Note: This Question is unanswered, help us to find answer for this one
72. How many copper layers are on a double-sided PCB?
Answer
Correct Answer:
Two
Note: This Question is unanswered, help us to find answer for this one
73. What is the English word for Pawl A?
Answer
Correct Answer:
Spring-loaded curved bar or lever
Note: This Question is unanswered, help us to find answer for this one
74. A lever with a free end that engages with a cogwheel or ratchet at a steep angle, what is known as?
Answer
Correct Answer:
Pawl A
Note: This Question is unanswered, help us to find answer for this one
75. What may a product be an assembly of multiple parts?
Answer
Correct Answer:
One part
Note: This Question is unanswered, help us to find answer for this one
76. What kind of piece is a custom-designed part?
Answer
Correct Answer:
Mechanical
Note: This Question is unanswered, help us to find answer for this one
77. What is an example of off-the-shelf software or hardware?
Answer
Correct Answer:
COTS - commercial off-the-shelf
Note: This Question is unanswered, help us to find answer for this one
78. What is a common term for ready-made off-the-shelf software or hardware products?
Answer
Correct Answer:
COTS
Note: This Question is unanswered, help us to find answer for this one
79. What is the initial sample created using?
Answer
Correct Answer:
Production tooling
Note: This Question is unanswered, help us to find answer for this one
80. What is used to check design and tune the tooling prior to making production?
Answer
Correct Answer:
Off-Tool Sample
Note: This Question is unanswered, help us to find answer for this one
81. OEMs produce complete, finished product for what other company?
Answer
Correct Answer:
Another company
Note: This Question is unanswered, help us to find answer for this one
82. What is a contract manufacturer that produces complete, finished product for another company?
Answer
Correct Answer:
OEM
Note: This Question is unanswered, help us to find answer for this one
83. What does ODM allow the brand firm to do?
Answer
Correct Answer:
Produce
Note: This Question is unanswered, help us to find answer for this one
84. What does ODM stand for?
Answer
Correct Answer:
Original Design Manufacturer
Note: This Question is unanswered, help us to find answer for this one
85. What is the default file format used by SolidWorks to store part models?
Answer
Correct Answer:
.SLDPRT
Note: This Question is unanswered, help us to find answer for this one
86. What type of connection is a groove?
Answer
Correct Answer:
Reduced diameter
Note: This Question is unanswered, help us to find answer for this one
87. What can be made in a mold?
Answer
Correct Answer:
Parts
Note: This Question is unanswered, help us to find answer for this one
88. What is the name of the container used to produce parts by giving shape to molten liquid material?
Answer
Correct Answer:
Mold
Note: This Question is unanswered, help us to find answer for this one
89. An approach that subdivides a system or a mechanism into smaller elements is called?
Answer
Correct Answer:
Modular design
Note: This Question is unanswered, help us to find answer for this one
90. On a smaller scale than the original, what is a model called?
Answer
Correct Answer:
Model A
Note: This Question is unanswered, help us to find answer for this one
91. What type of bodies are connected by joints?
Answer
Correct Answer:
Mostly rigid
Note: This Question is unanswered, help us to find answer for this one
92. How are the bodies in a mechanism usually connected?
Answer
Correct Answer:
By joints
Note: This Question is unanswered, help us to find answer for this one
93. Working together in a controlled manner in order to accomplish a desired force and/or motion transmission is known as what?
Answer
Correct Answer:
Mechanism
Note: This Question is unanswered, help us to find answer for this one
94. What can a lug be used for?
Answer
Correct Answer:
Support, to be used as a handle, or to allow mounting or attaching of another component
Note: This Question is unanswered, help us to find answer for this one
95. A projection attached to a metal part to provide support, to be used as a handle, or to allow mounting or attaching of another component is called what?
Answer
Correct Answer:
Lug
Note: This Question is unanswered, help us to find answer for this one
96. The advance during a single revolution is called what?
Answer
Correct Answer:
The lead
Note: This Question is unanswered, help us to find answer for this one
97. The axial travel in a single revolution is known as what?
Answer
Correct Answer:
Lead
Note: This Question is unanswered, help us to find answer for this one
98. The use of knurls on handles and knobs is used to what?
Answer
Correct Answer:
Roughen a turned surface
Note: This Question is unanswered, help us to find answer for this one
99. What is used to roughen a turned surface?
Answer
Correct Answer:
Knurling
Note: This Question is unanswered, help us to find answer for this one
100. What type of cut is Keyway A?
Answer
Correct Answer:
Slot
Note: This Question is unanswered, help us to find answer for this one
