SolidWorks Quiz # 5

What kind(s) of sketch entity does the Section View Command accept?

Any smooth path sketch

Only single line sketch

line sketch or simple curves

Continuous line sketch

Which is NOT an auto relief cut option?

Rectangular

Obround

Slot

Tear

What does the rip command do?

It copies an entire feature from one surface and pastes it on another

It separates a solid into a multi-body solid

It creates a relief gap necessary for the manufacturing of sheet metal

It breaks a solid along a corner to make it suitable for adding bends

What does the sheet metal parameter represent?

The length of the sheet metal

If a part has a Base Flange feature or not

If a part is cross sectioned

The bending radius of the sheet metal

Which of the following sketch command buttons is only available for 3D sketching?

Plane

Slot

Oval

Spline

What is the minimum number of constrains to fully define a polygon?

1

3

4

2

Which of the following features is available in both basic part design and surface design?

Extruded Boss

Chamfer

Revolved Cut

Fillet

To make sure your design criteria are satisfied at all time during your design process, which feature can you use to help you achieve such goal?

Sensor

Evaluate

Monitor

Statistics

Which is NOT a type of forming tool?

Emboss

Crest

Rib

Lance

Louver

Which solver uses an iterative approach to compute?

FFEPlus

Direct Sparse

None of them above

Both Direct Sparse and FFEPlus

By default, what happens to the newly inserted part, if you do not specify its location?

It gets lost!

The axes of the part and the assembly match, and the part floats

The axes of the part and the assembly match, and the part is fixed

The part position is centred around the assembly, and the part is fixed

The part position is centred on screen, and the part floats

If your base flange size indicates the maximum base area allowed, which of the Edge Flange Positions should be chosen?

Bend Outside

Bend Inside

Material Outside

Material Inside

Which one of these is NOT a beginning condition for an extrusion?

Body

Face

Sketch Plane

Vertex

What do you need to sketch to create a centerline between two existing parallel edges?

You must need dimensioning if only one centerline is sketched.

You need at least two sketched centerlines.

You can create it by sketching one centerline without dimensioning.

You only need to sketch the centerline, as long as it snaps at the right position.

Which of the following combinations is not sufficient for a "Width" mate?

None of the above

Two parallel faces from one part and a cylindrical face

Four parallel faces with two from each part

A center plane from one part and two parallel faces from the other

When designing a sheet metal part, what relief option do you NOT have?

Bend Waist

Auto Relief

Square Relief

Circular Relief

Which of the following sketch entities needs to be avoided when defining hole positions in Hole Wizard?

Polygon

Center Point Arc

Perimeter Circle

Center Rectangle

Which property do you not assign to a custom material in SolidWorks?

Viscosity

Cross hatch

Thermal conductivity

Mass density

Tensile strength

Along a ripped edge of a sheet metal part which is not a corner type?

Open Butt

Overlap

Closed Butt

Underlap

What tool do you use to rotate a drawing view out of its plane?

Standard three views

Auxiliary view

3D drawing view

Section View

Rotate view

When you work with sheet metal parts, which tool you do not use to create holes?

Form tool

Extrude

Fold

Vent

Simple Hole

Which of the following represents the flange length, excluding the bending radius?

Inner virtual sharp length

None of these

True flange length

Outer virtual sharp length

When you work with FloXpress, what fluids flowing through your model do you select from?

Water, Air

Newtonian liquid, ideal gas

Any liquid, any gas

Newtonian liquid, any gas

How many sections can you create using a "section view" tool?

No limit

4

1

2

3

Which file contains all the drawing document-specific information, such as specifications for units, drafting standard, font selections, etc?

SOLIDWORKS drawing template

SOLIDWORKS composer file

SOLIDWORKS part file

SOLIDWORKS sheet format

You need to design a steel spring with a pitch diameter of 3 inches, free length of 10 inches, and pitch of 1 inch. How would you accomplish this in SOLIDWORKS?

Create a new sketch of a circle with a diameter of 1 inch. Then use the Helix/Spiral curve command and define a height of 10 inches and pitch of 3 inches.

Create a new sketch of a circle with a diameter of 3 inches. Then use the Helix/Spiral curve command to define a height of 10 inches and pitch of 1 inch.

First, create a new sketch of a circle of 10 inches. Then use the Helix/Spiral curve command and define by pitch of 1 inch and 3 revolutions.

Use the Helix/Spiral curve command and define a diameter of 3 inches, height of 10 inches, and pitch of 1 inch.

Which choice is NOT a fillet type in SOLIDWORKS?

Constant size

Variable size

Face

Angled

Your sketch is not extruding correctly. It does not seem to be a properly closed contour, although from a simple visual inspection, it looks to be fully closed. You think perhaps there are some very small gaps in your contour that are causing the issue. What tool can you use to find these small gaps?

Quick Snaps

Rebuild

Repair Sketch

Show Error

Which choice is an example of a skected feature?

Chamfer

Extrusion

Fillet

Shell

You want to make two circles have the same center point within a SOLIDWORKS sketch. How can you do this?

Add a tangent relation between the circles

Add a concentric relation between the circles

Add a horizontal relation between the circles

Add an equal relation between the circles