The ratio of shearing stress to shearing strain within elastic limit, is known as
Answer
Correct Answer:
Shear modulus of elasticity
Note: This Question is unanswered, help us to find answer for this one
Choose the incorrect statement from the following:
Answer
Correct Answer:
The diameter of a rivet hole is equal to the nominal diameter of the rivet plus 1.5 mm
Note: This Question is unanswered, help us to find answer for this one
The maximum permissible slenderness ratio of a member carrying loads resulting from wind, is
Answer
Correct Answer:
250
Note: This Question is unanswered, help us to find answer for this one
The rolled steel I-sections are most commonly used as beams because these provide
Answer
Correct Answer:
Large moment of inertia with less cross-sectional area
Note: This Question is unanswered, help us to find answer for this one
The effective length of a compression member of length L held in position and restrained in direction at one end and effectively restrained in direction but not held in position at the other end, is
Answer
Correct Answer:
L
Note: This Question is unanswered, help us to find answer for this one
For a rectangular section, the ratio of the maximum and average shear stresses, is
Answer
Correct Answer:
1.5
Note: This Question is unanswered, help us to find answer for this one
The average shear stress for rolled steel beam section, is
Answer
Correct Answer:
945 kg/cm2
Note: This Question is unanswered, help us to find answer for this one
Column footing is provided
Answer
Correct Answer:
To spread the column load over a larger area
Note: This Question is unanswered, help us to find answer for this one
The distance between e.g. of compression and e.g. of tension flanges of a plate girder, is known as
Answer
Correct Answer:
Effective depth
Note: This Question is unanswered, help us to find answer for this one
If d is the distance between the flange angles, the vertical stiffeners in plate girders are spaced not greater than
Answer
Correct Answer:
1.5 D
Note: This Question is unanswered, help us to find answer for this one
Select the correct statement from the following:
Answer
Correct Answer:
Vertical stiffeners may be placed in pairs one on each side of the web
Note: This Question is unanswered, help us to find answer for this one
In plastic analysis, the shape factor for circular sections, is
Answer
Correct Answer:
1.697
Note: This Question is unanswered, help us to find answer for this one
The minimum edge distance of a rivet line connecting two or more plates, is kept equal to 37 mm plus (where t is the thickness in mm of the thinner outside plate).
Answer
Correct Answer:
4 t
Note: This Question is unanswered, help us to find answer for this one
For determination of allowable stress in axial compression, Indian Standard Institution has adopted
Answer
Correct Answer:
Secant formula
Note: This Question is unanswered, help us to find answer for this one
Tongue plates are provided in a steel girder at
Answer
Correct Answer:
The upper and lower ends of the web.
Note: This Question is unanswered, help us to find answer for this one
The method of design of steel framework for greatest rigidity and economy in weight, is known as
Answer
Correct Answer:
Fully rigid design
Note: This Question is unanswered, help us to find answer for this one
Pick the correct statement from the following:
Answer
Correct Answer:
Dead load includes self-weight of the structure and super-imposed loads permanently attached to the structure
Note: This Question is unanswered, help us to find answer for this one
The ratio of longitudinal stress to strain within eiastic limit, is known as
Answer
Correct Answer:
Modulus of elasticity
Note: This Question is unanswered, help us to find answer for this one
The permissible stress in bending for rolled steel I-beams and channels, is
Answer
Correct Answer:
1650 kg/cm2
Note: This Question is unanswered, help us to find answer for this one
Pick up the correct statement from the following:
Answer
Correct Answer:
When the gauge distance is larger than the pitch, the failure of the section may occur in a zig-zag line
Note: This Question is unanswered, help us to find answer for this one
